Colocado por: nunoreismendoncasoluções interessantes para piso radiante em situações de remodelação.
Colocado por: ns03Eu tenho piso radiante eletrico combinado com soalho flutuante e estou satisfeito com o rendimento.
Colocado por: danobrega
Diga-me uma coisa ns03, sabe se lhe ligaram o equipamento antes de colocar o flutuante? Estive a ler o manual do flutuante que em princípio vou colocar e as instruções metem medo...
Colocado por: nandogonca
Que marca de flutuante? Eu também tenho PRE e flutuante em 2 divisões e a marca KRONOTEX não assusta nas instruções...
Colocado por: sergyio
ate acho que nem dizem nada de especial sobre o piso radiante, pois não?
Colocado por: nandogonca
Acho que só falam de ser possível... Já não me lembro se foi neles ou noutros que falam num aquecimento gradual.
Colocado por: nandogoncaQue marca de flutuante? Eu também tenho PRE e flutuante em 2 divisões e a marca KRONOTEX não assusta nas instruções...
Screeds must be installed in accordance with industry standards. All mineral sub-floors must be heated
before the installation of Kaindl floors, so that no more harmful moisture can be released. This heating
process is required throughout all the seasons. Cement screeds can be heated three weeks after
installation, anhydrite screeds after just one week.
The temperature must be raised by increments of 5°C/9°F per day until the maximum heating output is
reached. This is also important for all the following heating periods. The time you have to maintain the
maximum heating by running full load depends on type and thickness of the screed.
Cement screed: per cm screed thickness 1 day
Anhydrite screed: per cm screed thickness 2 days
After this full load heating phase the temperature has to be decreased by reductions of 5°C/9°F per
day. For reasons of security it is necessary to repeat the procedure of heating the screed.
If the heating and cooling procedure is carried out by the heating installation contractor he should
automatically compile and submit a heating report. Questions should always be raised if this report is
missing.
Before the installation, moisture should be tested with CM-machines at the points marked by the
screed installers and the heating installation contractors. The permissible moisture for cement screed
is max. 1.8 CM-% and for anhydrite screed max. 0.3 CM-%.
Important: to test the dryness of the screed bedding, lay out several pieces of PE foil (ca. 50 x 50
cm/20 x 20'') and seal off the edges. If no condensation has collected, it is clear that the screed is dry
and the installation process can be started.
The temperature of the under floor heating system could be raised again progressively to the required
output 24 hours after the Kaindl floor is installed
Note: This also applies for the beginning of each heating period.
And please note one further fundamental rule:
The surface temperature of your laminated floor covering should not exceed 26°C/79°F. An ideal
climate during the heating period is a temperature of 20 - 22°C/68 – 72°F and a humidity of 50 - 60%.
Please note: it is imperative that a non-pervious building foil with a thickness of at least 0,2mm
is laid over the whole surface.
The chosen footstep sound insulation can now be laid on the building foil. If it is not possible to
maintain a constant room temperature, a slight opening of joints may occur. This joint opening is not a
defect, it is a consequence of the natural properties of wood and wood products. This should be borne
in mind particularly during changes of climate.
Colocado por: TROLHA...quando chegar altura de finalizar o piso radiante,o chão já está mais que seco!!
Colocado por: danobrega
Diga-me uma coisa ns03, sabe se lhe ligaram o equipamento antes de colocar o flutuante? Estive a ler o manual do flutuante que em princípio vou colocar e as instruções metem medo...